With the advancement of technology and economic development, more and more users of peanut shelling machines have been purchased, but many of them have failed to fully understand the proper use of peanut shelling machines due to their failure to fully understand the correct use of peanut shelling machines. Out, not only causes the shelling quality to be poor, but also the efficiency is low, which seriously affects its economic and social benefits. Therefore, it is necessary to introduce the correct use of the aircraft.
First, the correct use of peanut sheller several requirements on the shelling machine requirements: If the shelling clean, high productivity, the cleaning device for the shelling machine, requires a higher degree of cleanliness in order to improve the machine tool Utilization rate.
The requirements for peanuts (skin fruit): peanuts should be suitable for dry and wet, too dry the broken rate is high; too wet will affect the work efficiency. Peanuts (leathers) stored in rural areas are generally relatively dry. The following methods are suitable for making them dry and wet:
(1) Shelling in winter. Before shelling, evenly spray about 50 kilograms of fruit with about 10 kilograms of warm water and cover it with plastic film for about 10 hours. Then cool it in the sun for about 1 hour to start shelling. Cover with plastic film for other seasons. About 6 hours, the rest can be the same.
(2) The relatively dry peanut (Pluto) may be invaded in a large pool, immediately after dipping, it is removed and covered with a plastic film for about one day, and then it is exposed to cool sunlight in the sun.
Voltage requirements and workplace choices: Single-phase motors must operate normally and the voltage must reach its rated voltage. In rural areas, there is usually only one transformer in a village, and households are scattered. In addition, the wires and circuits used are not very standard. As a result, the voltage of users far away from the transformer is insufficient. Therefore, the workplace should be located closer to the transformer.
Second, the operating method and precautions
1. Before use, check whether the fasteners are tightly tightened, whether the rotating part is flexible, whether the bearings have lubricating oil, and the shelling machine should be placed on a stable ground.
2. Before use, check the power supply and voltage. The switch must be in the open position.
3. After the motor is started, the rotation of the rotor should be consistent with the direction indicated on the machine. Let idling for a few minutes first, and observe if there is any abnormal noise. When it is working normally, feed peanuts evenly.
4. When peanuts are fed, they should be uniform and moderate in quantity, and they must not contain iron scraps, stones, etc. to prevent breaking of peanuts and mechanical accidents. When the peanuts cover the screen surface, you can open the rice mouth switch.
5. Select the appropriate screen according to the size of the peanuts.
6. When the number of peanut shells in the main flower pot increases, the motor can be moved downwards to tighten the fan belt and increase the amount of air blowing.
7, when operating, people do not stand on the belt drive side, so as not to hurt.
8, after a period of use, ready to store the machine, you should remove its clean appearance of dust, dirt and debris and other debris inside. The machine should be covered and placed in a dry warehouse to avoid the sun and the rain.
9, remove the belt and keep it separately.
10, use diesel oil to clean all parts of the bearing, clean, dry and buttered.
11. The transmission parts and the bearing chamber should be maintained with sufficient lubricating oil and cleaned and replaced regularly.
First, the correct use of peanut sheller several requirements on the shelling machine requirements: If the shelling clean, high productivity, the cleaning device for the shelling machine, requires a higher degree of cleanliness in order to improve the machine tool Utilization rate.
The requirements for peanuts (skin fruit): peanuts should be suitable for dry and wet, too dry the broken rate is high; too wet will affect the work efficiency. Peanuts (leathers) stored in rural areas are generally relatively dry. The following methods are suitable for making them dry and wet:
(1) Shelling in winter. Before shelling, evenly spray about 50 kilograms of fruit with about 10 kilograms of warm water and cover it with plastic film for about 10 hours. Then cool it in the sun for about 1 hour to start shelling. Cover with plastic film for other seasons. About 6 hours, the rest can be the same.
(2) The relatively dry peanut (Pluto) may be invaded in a large pool, immediately after dipping, it is removed and covered with a plastic film for about one day, and then it is exposed to cool sunlight in the sun.
Voltage requirements and workplace choices: Single-phase motors must operate normally and the voltage must reach its rated voltage. In rural areas, there is usually only one transformer in a village, and households are scattered. In addition, the wires and circuits used are not very standard. As a result, the voltage of users far away from the transformer is insufficient. Therefore, the workplace should be located closer to the transformer.
Second, the operating method and precautions
1. Before use, check whether the fasteners are tightly tightened, whether the rotating part is flexible, whether the bearings have lubricating oil, and the shelling machine should be placed on a stable ground.
2. Before use, check the power supply and voltage. The switch must be in the open position.
3. After the motor is started, the rotation of the rotor should be consistent with the direction indicated on the machine. Let idling for a few minutes first, and observe if there is any abnormal noise. When it is working normally, feed peanuts evenly.
4. When peanuts are fed, they should be uniform and moderate in quantity, and they must not contain iron scraps, stones, etc. to prevent breaking of peanuts and mechanical accidents. When the peanuts cover the screen surface, you can open the rice mouth switch.
5. Select the appropriate screen according to the size of the peanuts.
6. When the number of peanut shells in the main flower pot increases, the motor can be moved downwards to tighten the fan belt and increase the amount of air blowing.
7, when operating, people do not stand on the belt drive side, so as not to hurt.
8, after a period of use, ready to store the machine, you should remove its clean appearance of dust, dirt and debris and other debris inside. The machine should be covered and placed in a dry warehouse to avoid the sun and the rain.
9, remove the belt and keep it separately.
10, use diesel oil to clean all parts of the bearing, clean, dry and buttered.
11. The transmission parts and the bearing chamber should be maintained with sufficient lubricating oil and cleaned and replaced regularly.
Single Arm Electric Medical Pendant,The control cabinet of the Tower Crane adopt the imported high-strength aluminum alloy of patent technology for the one-off extrusion molding, and the surface undergoes the primary oxidation treatment.The tray surface is non-slip. Mechanical friction damping brake.The imported electrical machine is adopted , and the rising and rotation function of the electric horizontal cantilever can accurately position without excursion.The gas pipeline, power supply and computer communication line are separately arranged without interference.
Single Arm Electric Surgical Pendant
Single Arm Electric Surgical Pendant,Single Arm Anesthesia Pendant,Single Arm Ceiling Pendant,Single Arm Medical Gas Pendant
Shandong Lewin Medical Equipment Co., Ltd. , https://www.operatinglight.nl